firestopping products

Choose Your Product Category

1 and 2 hour UL Fire Rated

Fire rated light enclosure series have been designed to help maintain the integrity of fire rated ceilings when penetrated by recessed lights, fluorescent fixtures or in-ceiling loudspeakers.

1 hour UL Fire Rated

Fire Rated Troffer Cover series is the ONLY fully UL tested products that have been designed to help maintain the integrity of fire rated ceilings when penetrated by troffers or fluorescent fixtures.

1 hour Fire Protection

Dome-shaped intumescent cover which has been designed to help maintain the integrity of fire rated ceilings when penetrated by in-ceiling loudspeakers and acoustic rating of the structure.

UL Classified Penetrations

Intumescent Penetration Product designed to fireproof wire, pipe, and cable penetrations in walls or ceilings. Easy to install and allow for retroactive installations or new construction.

FIRE RATED LIGHT COVERS

FF109X

2 Hour Fire Rated Recessed Light Cover

$56.40

Inside Height: 8" Diameter: 17"

PRODUCT INFORMATION

The FF109X is the only two hour UL tested and approved fire barrier that can be used with a wide range of recessed lights to effectively prevent the spread of flames through a ceiling opening. Once a hole is made in the drywall to install recessed lights or speakers, the integrity of the construction and its ability to perform in a fire is reduced significantly, creating a potential fire hazard.

This is the reason why the International Building Code states:

Where floor/ceiling assemblies are required to have a 1 or 2-hour fire resistance rating, recessed fixtures shall be installed such that the required fire resistance of the ceiling will not be reduced”

The FF109X is two hour approved for every major ceiling assembly including gypsum, sheetrock, drywall, acoustical tiles and suspended ceilings with any joist spacing up to 24 inch on center. The enclosure is made out of an intumescent material which will be activated in case of a fire, stopping both, flame spread and heat transmission for two hours.

Tenmat 2 Hour Fire Rated Light Covers are UL tested and approved for use with IC-rated recessed incandescent, fluorescent, LED light fixtures.TENMAT Fire Rated Light Covers can be used with most light manufacturer’s models and are suitable for new construction as well as remodel projects.

In addition to its fire protection capabilities, the FF109X also exhibits excellent thermal and acoustical insulating properties to save energy and reduce noise. The flexible and lightweight nature of the covers makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions.

BENEFITS
  • 120 minute protection.
  • UL tested and approved for use with IC-rated recessed incandescent, fluorescent or LED light fixtures.
  • For Joist Spacing up to 24″ on center.
  • Suitable for 2″x10″, 2″x12″, 2″x14″ and 2″x16″.
  • Can be used in floor/ceiling, as well as roof/ceiling assemblies (attic).
  • UL Fire Tested to maintain fire ratings of two hours or less in all UL L500, D500, G500, D200, G200, J200 and L200 series fire-rated floor/ceiling assemblies.
  • UL Fire Tested to maintain fire ratings of one hour or less for all UL P200 and P500 series fire-rated roof/ceiling assemblies.
  • Significant Labor savings.
  • Lightweight (approx. 2.5 lbs).
  • Flexible material enables cover to be fitted around obstructions or retro-fitted.
  • Enhances the acoustic protection of the ceiling.
  • Reduces heat loss through the fixture.
  • Maintenance free.

FF109-300

1 Hour Fire Rated Recessed Light Cover

$47.95

Inside Height: 8" Diameter: 13"

PRODUCT INFORMATION

The FF109-300 UL Fire Rated cover is a dome-shaped intumescent cover which has been designed to help maintain the integrity of fire rated ceilings when penetrated by recessed fixtures.

Tenmat Fire Rated Light Covers are UL tested and approved for use with IC-rated recessed incandescent, fluorescent, and LED light fixtures.

The unique design gives the architect, specifier and installer more freedom in fixture selection as the covers are suited to a wide range of recessed fixtures. The flexible and lightweight nature of the covers makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions.The high expansion and insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.

Inside Height 8″

Diameter 13″

Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Easy Installation – can be fitted in seconds – no screws, drilling or additional sealant required.
  • UL tested and approved for use with IC-rated recessed incandescent, fluorescent or LED light fixtures.
  • For solid wood joists, open-web wood trusses or I-shaped wood joists on max 16″ on center.
  • Significant Labor savings.
  • Lightweight (approx. 1.5 lbs).
  • Flexible material enables cover to be fitted around obstructions or retro-fitted.
  • Two vent holes in the cover reduce the risk of over-heating of the light in normal use.
  • In a fire, the intumescent material expands 5 times of its original thickness, closing the vent holes and preventing flame spread.
  • Easy to remove and re-install for fixture maintenance.
  • Enhances the acoustic protection of the ceiling.
  • Reduces heat loss through the fixture.
  • Maintenance free.
  • 60 minute protection.

FF109-350

1 Hour Fire Rated Recessed Light Cover LARGE

$52.64

Inside Height: 11" Diameter: 15"

PRODUCT INFORMATION

The FF109-350 1 Hour fire rated light cover is a dome-shaped intumescent cover which has been designed to help maintain the integrity of fire rated ceilings when penetrated by recessed fixtures.

The flexible and lightweight nature of the fire rated light cover makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions.The high expansion and insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.

Inside Height 11″

Diameter 15″

Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Easy Installation – can be fitted in seconds – no screws, drilling or additional sealant required.
  • Fits most popular fixtures.
  • Significant Labor savings.
  • Lightweight (approx. 2.5 lbs).
  • Flexible material enables cover to be fitted around obstructions or retro-fitted.
  • Two vent holes in the cover reduce the risk of over-heating of the light in normal use.
  • In a fire, the intumescent material expands 5 times of its original thickness, closing the vent holes and preventing flame spread.
  • Easy to remove and re-install for fixture maintenance.
  • Enhances the acoustic protection of the ceiling.
  • Reduces heat loss through the fixture.
  • Maintenance free.
  • 60 minute protection.

FF109-200

1 Hour Fire Rated LED Downlight Cover

$34.80

Inside Height: 7" Diameter: 7-7/8"

PRODUCT INFORMATION

The FF109-200 1 Hour Fire Rated LED Downlight Cover is a cone-shaped intumescent enclosure which has been specifically designed to help maintain the integrity of openings of up to 4” diameter in fire rated ceilings when penetrated by modern low profile LED downlight fixtures.

 

The ultra-flexible nature of the material allows the cover to get rolled up for easy retrofit, remodel or new construction installation from below the ceiling to protect modern low profile LED light fixture and provide a 60 minute flame, smoke and heat barrier.

 

The FF109-200 Low-Profile LED Recessed Light Cover is suitable for most low profile LED lights, ultra-thin wafer LED recessed lights, LED recessed retrofit downlights, LED recessed ceiling light and recessed spotlight remodel kits installed in floor/ceiling or roof/ceiling assemblies (attic spaces).

 

The unique design gives the architect, specifier and installer more freedom in fixture selection as the covers are suited to a wide range of LED downlights.

 

The flexible and lightweight nature of the fire rated light cover makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions. The high expansion and insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.

 

Inside Height 7″

Diameter 7-7/8″

Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Only fire tested solution for retrofit applications.
  • Easy Installation – can be fitted in seconds – no screws, drilling or additional sealant required.
  • Fits most 4” low profile LED downlight fixtures.
  • Significant Labor savings.
  • Lightweight (only 8 oz.).
  • Flexible material enables the cover to be fitted around obstructions or retro-fitted.
  • Vent hole on top of the cover reduces the risk of over-heating of the light in normal use.
  • In a fire, the intumescent material expands 5 times of its original thickness, closing the vent hole and preventing flame spread.
  • Easy to remove and re-install for fixture maintenance.
  • Enhances the acoustic protection of the ceiling.
  • Reduces heat loss through the fixture.
  • Maintenance free.
  • 60-minute protection.

FF109-250

1 Hour Fire Rated LED Downlight Cover LARGE

$37.20

Inside Height: 10" Diameter: 9-7/8"

PRODUCT INFORMATION

The FF109-250 1 Hour Fire Rated LED Downlight Cover is a cone-shaped intumescent enclosure which has been specifically designed to help maintain the integrity of openings of up to 6” diameter in fire rated ceilings when penetrated by modern low profile LED downlight fixtures.

The ultra-flexible nature of the material allows the cover to get rolled up for easy retrofit, remodel or new construction installation from below the ceiling to protect modern low profile LED light fixture and provide a 60 minute flame, smoke and heat barrier.

The FF109-250 Low-Profile LED Recessed Light Cover is suitable for most low profile LED lights, ultra-thin wafer LED recessed lights, LED recessed retrofit downlights, LED recessed ceiling light and recessed spotlight remodel kits installed in floor/ceiling or roof/ceiling assemblies (attic spaces).

The unique design gives the architect, specifier and installer more freedom in fixture selection as the covers are suited to a wide range of LED downlights.

The flexible and lightweight nature of the fire rated light cover makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions. The high expansion and insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.

Inside Height 10″

Diameter 9-7/8″

Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Only fire tested solution for retrofit applications.

  • Easy Installation – can be fitted in seconds – no screws, drilling or additional sealant required.

  • Fits most 4” and 6” low profile LED downlight fixtures.

  • Significant Labor savings.

  • Lightweight (only 11 oz.).

  • Flexible material enables the cover to be fitted around obstructions or retro-fitted.

  • Vent hole on top of the cover reduces the risk of over-heating of the light in normal use.

  • In a fire, the intumescent material expands 5 times of its original thickness, closing the vent hole and preventing flame spread.

  • Easy to remove and re-install for fixture maintenance.

  • Enhances the acoustic protection of the ceiling.

  • Reduces heat loss through the fixture.

  • Maintenance free.

  • 60-minute protection.

FIRE RATED TROFFER COVERS

FF130-2'x 2' 1 Hour UL Fire Rated Troffer Cover

Minimum Order Quantity: 6 Units

$66.20/unit

Inside Height: 5" Length: 2' Width: 2'

PRODUCT INFORMATION

The FF130-2’x2′ Troffer Protection Cover is the ONLY fully UL fire tested solution for 2′ by 2′ fluorescent fixtures on the market. The cover is a pre-formed flexible enclosure which has been designed to help maintain the integrity of fire rated ceilings when penetrated by 2′ by 2′ fluorescent fixtures.

The flexible and lightweight nature of the covers makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions. The FF130 Cover can be folded to ease installation in restricted spaces.

The insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.


Inside Height 5″


Length 2′


Width 2′


Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Simple Installation — can be fitted in seconds.
  • Significant Labor Saving — ready to install product requiring no assembly, cutting, drilling, screwing or additional sealant required.
  • Lightweight (5 lbs).
  • Suitable for lay-in tile ceilings.
  • Easy to remove and re-install for fixture maintenance.
  • Enhances the acoustic protection of the ceiling.
  • Reduces heat loss through the fixture.
  • Cable entry points can be made anywhere on the sides and top for ease of wiring of the fixture.
  • Maintenance free.
  • 60 minute protection.

FF130-2'x 4' 1 Hour UL Fire Rated Troffer Cover

Minimum Order Quantity: 6 Units

$69.95/unit

Inside Height: 5" Length: 4' Width: 2'

PRODUCT INFORMATION

The FF130-2’x4’ Troffer Protection Cover is the ONLY fully UL fire tested solution to provide a 1 Hour Fire Rating for fire rated ceilings when penetrated by 2′ by 4′ fluorescent fixtures. It is a pre-formed flexible cover and does not require any assembly, making it the smart choice for new construction, as well as remodel projects.

The unique design gives the architect, specifier and installer more freedom in fixture selection as the covers are suited to a wide range of these fixtures.

The flexible and lightweight nature of the covers makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions. The FF130 Cover can be folded to ease installation in restricted spaces.

The insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.


Inside Height 5″


Length 4′


Width 2′


Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Simple Installation – can be fitted in seconds.
  • Significant Labor Saving – ready to install product requiring no assembly, cutting, drilling, screwing or additional sealant required.
  • Lightweight (9 lbs).
  • Suitable for lay-in tile ceilings.
  • Easy to remove and re-install for fixture maintenance.
  • Enhances the acoustic protection of the ceiling.
  • Reduces heat loss through the fixture.
  • Cable entry points can be made anywhere on the sides and top for ease of wiring of the fixture.
  • Maintenance free.
  • 60 minute protection

FIRE RATED SPEAKER COVERS

FF109-FRSC

1 Hour Fire Rated Speaker Cover

Free Shipping

$120.00

Inside Height: 8" Diameter: 13"

PRODUCT INFORMATION

The FF109 Fire rated speaker cover is a dome-shaped intumescent cover which has been designed to help maintain the integrity of fire rated ceilings when penetrated by in-ceiling loudspeakers and acoustic rating of the structure.

The unique design gives the architect, sound professional and installer more freedom in speaker selection as the covers are suited to a wide range of speaker sizes.

The flexible and lightweight nature of the covers makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions.

The high expansion and insulating properties of the cover ensures that both, flame spread and heat transmission, are stopped for 60 minutes.

Inside Height 8″

Diameter 13″

Data Sheets and classification cards available from the Downloads tab.

BENEFITS
  • Can be used with any speaker manufacturer.
  • Enhances the acoustic protection of the ceiling.
  • Easy Installation – can be fitted in seconds – no screws, drilling or additional sealant required.
  • Significant Labor savings.
  • Lightweight (approx. 1.5 lbs).
  • Flexible material enables cover to be fitted around obstructions or retro-fitted.
  • For ceiling cut-outs of up to 10 5/8″
  • Two vent holes in the cover reduce the risk of over-heating of the light in normal use.
  • In a fire, the intumescent material expands 5 times of its original thickness, closing the vent holes and preventing flame spread.
  • Easy to remove and re-install for speaker maintenance.
  • Reduces heat loss through the speaker fixture.
  • Maintenance free.
  • 60 minute protection.

RELATED PRODUCTS

Intumescent Paint

Fireproofing Patch

Need Help With TechMat Supply? We Are Experts!

Free Consultations

Scroll to Top